Jensen Car Stereo System PADIN5 User Manual

PADIN5  
Installation and Operation Manual  
Instruction d’installation et d’opération  
PADIN5  
 
PADIN5  
PRECAUTIONS  
Use the Proper Power Supply.  
This product is designed to operate with a 12 volt DC, negative ground battery system (the  
standard system in a North American car).  
Use Authorized Service Centers.  
Do not attempt to disassemble or adjust this precision product; contact a professional for  
assistance.  
Avoid Moisture.  
To reduce the risk of fire or electric shock, do not expose this equipment to rain or moisture.  
Use Recommended Accessories.  
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK AND ANNOYING  
INTERFERENCE, USE ONLY THE RECOMMENDED ACCESSORIES.  
PREPARATION  
It’s a good idea to read all of the instructions before beginning the installation. We recommend  
having your Jensen PADIN5 installed by a reputable installation shop.  
Tools and Supplies  
You will need these tools and supplies to install your PADIN5:  
Torx type, flat-head and Philips screwdrivers  
Wire cutters and strippers  
Tools to remove existing radio (screwdriver, socket wrench set or other tools)  
Electrical tape  
Crimping tool  
Volt meter/test light  
Crimp connections  
18 gauge wire for power connections  
16 – 18 gauge speaker wire  
Speaker Requirements: Only connect speakers rated in the load impedance of 4 ohms.  
Speakers with a load impedance less than 4 ohms could damage the unit.  
Disconnecting the Battery  
To prevent a short circuit, be sure to turn off the ignition and remove the negative (-) battery cable  
prior to installation.  
NOTE: If the PADIN5 is to be installed in a vehicle equipped with an on-board drive or  
navigation computer, do not disconnect the battery cable. If the cable is disconnected, the  
computer memory may be lost. Under these conditions, use extra caution during  
installation to avoid causing a short circuit.  
1
 
PADIN5  
INSTALLATION  
Before you begin, always disconnect the battery negative terminal.  
4. Place the unit in front of the dashboard opening so the wiring can be brought through the  
mounting sleeve.  
Universal Installation Using Mounting Sleeve  
1. Slide the mounting sleeve off of the chassis if it has not already been removed. If it is locked  
into position, use the removal keys (supplied) to disengage it.  
8
2. Check the dashboard opening size by sliding the mounting sleeve into it. If the opening is not  
large enough, carefully cut or file as necessary until the sleeve easily slides into the opening.  
Do not force the sleeve into the opening or cause it to bend or bow. Check that there will be  
sufficient space behind the dashboard for the radio chassis.  
7
3. Locate the series of bend tabs along the top, bottom and sides of the mounting sleeve. With  
the sleeve fully inserted into the dashboard opening, bend as many of the tabs outward as  
necessary to firmly secure the sleeve to the dashboard.  
5
P
A
DIN5  
4
5. Follow the wiring diagram carefully and make certain all connections are secure and  
insulated with crimp connectors or electrical tape to ensure proper operation.  
6. After completing the wiring connections, turn the unit on to confirm operation (vehicle ignition  
switch must be on). If the unit does not operate, recheck all wiring until the problem is  
corrected. Once proper operation is achieved, turn the ignition switch off and proceed with  
final mounting of the chassis.  
7. Carefully slide the unit into the mounting sleeve making sure it is right-side-up until it is fully  
seated and the spring clips lock it into place.  
8. Attach one end of the perforated support strap (supplied) to the screw stud on the rear of the  
chassis using the hex nut provided. Fasten the other end of the perforated strap to a secure  
part of the dashboard either above or below the radio using the screw and hex nut provided.  
Bend the strap, as necessary, to position it.  
CAUTION: The rear of the unit must be supported with the strap to prevent damage to the  
dashboard from the weight of the radio or improper operation due to vibration.  
9. Test operation by referring to the operating instructions for the unit.  
2
 
PADIN5  
Wiring  
Perform the following steps to install the radio using a wiring adapter  
(purchased separately):  
1. Splice or crimp wires.  
DVDB01 Connector (DVD Player Sold Separately)  
2. Attach wiring adapter to vehicle wiring harness.  
3. Re-connect the battery negative terminal and test radio operation to  
confirm correct wiring.  
Jensen Connector  
1
2
5
Rear Radio Controls and Connectors  
1. MICROPHONE CONNECTIONS  
See “Using Microphones” on page 6.  
2. IR CONNECTIONS  
See “AUX IR and DVD IR Connections” on page 5.  
3. RADIO IN LOW/HIGH SWITCH  
Select “LOW” when you are using low-level RCA radio input (RADIO  
LOW-IN).  
Select “HIGH” when using hi-level radio input (RADIO HI-IN).  
4. RCA CONNECTIONS  
RADIO LOW-IN: Connect to the RCA output from your radio.  
AUX IN 1 and AUX IN 2: See “AUX RCA Connections” on page 5.  
AUDIO OUT: Connect to an additional amplifier.  
DVD IR  
5. HIGH LEVEL WIRING CONNECTIONS  
See Table 1 on page 4 for specific wiring connections.  
1
2
3
4
3
 
PADIN5  
Table 1: Wiring Connections  
PADIN5 Connector PIN View  
Pin # Wire Color  
SPEAKER OUT  
Function  
1
White  
Driver Speaker L+  
9
5
6
7
8
1
2
3
4
2
Gray  
Driver Speaker R+  
3
Green  
Passenger Speaker L+  
Passenger Speaker R+  
Driver Speaker L-  
1
4
2
5
1
3
2
4
3
6
10  
11  
12  
4
Violet  
5
White/Black  
Gray/Black  
Green/Black  
Violet/Black  
Orange  
6
Driver Speaker R-  
7
Passenger Speaker L-  
Passenger Speaker R-  
EXT Speaker +  
8
POWER  
RADIO HI-IN  
9
10  
Orange/Black  
White/Red  
White/Blue  
EXT Speaker -  
11  
Trigger DC +12V output for AUX2 mode  
Trigger DC +12V output for AUX1 mode  
SPEAKER OUT  
12  
POWER  
1
Red  
DC Input: Connect to +12V switched power source. The radio will not work if this  
wire is not connected.  
2
3
4
5
6
Pink  
Trigger +12V Output for DVD mode  
+12V Plus Constant Power  
Not Used  
Yellow  
Empty  
Blue/White  
Black  
Trigger +12V Output  
Ground  
RADIO HI-IN  
1
2
3
4
White  
Speaker Left +  
Speaker Right +  
Speaker Left -  
Speaker Right -  
Gray  
White/Black  
Gray/Black  
4